Daylight Harvesting Function Bare Board High Altitude Install
Motion Sensor
Daylight harvesting of dc sensor:
| Daylight Harvesting: When ambient lux value is lower than preset lux value(30Lux, 50Lux,
80Lux or 120Lux), light on when detect movement and adjust artificial lighting to
keep the brightness balancing; When ambient brightness is higher than preset lux value,
lamp will still remain off even no movement detected. |
| Precondition of Daylight Harvesting: as picture 1. Daylight threshold is on 30Lux, 50Lux, 80Lux or 120Lux. 2. Hold time is on 5s/30s/1min/3min/5min/10min/20min/30min |
When ambient lux value is lower than preset lux value(30Lux, 50Lux,
80Lux or 120Lux),
light on when detect movement and adjust artificial lighting to
keep the brightness
balancing; When ambient brightness is higher than preset lux value,
light off.
When ambient brightness is higher than preset lux level, light will automatically turn off.
Technical date of dc motion sensor:
| Operating voltage | 10-15VDC |
| Detection area | 25%/50%/75%/100% |
| Operating current | ＜30mA |
| Output | DIM 0-10V |
| Stand-by power | <0.5W |
| Hold time | 5s/30s/1min/3min/5min/10min/20min/30min |
| Daylight threshold | 2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/Disable |
| Stand-by period | 0s/10s/30s/1min/5min/10min/30min/+∞ |
| Stand-by dimming level | 10%/20%/30%/50% |
| Operating termperature | -20°C~+60°C |
Microwave power | <0.3mW |
Microwave frequency | 5.8GHz±75MHz |
Factory Default Setting: Detection area 100%/ Hold time 5s/
Daylight threshold Disable/Stand-by
period 0s/Stand-by dimming level 10%.
Features of Sensor:
1. Daylight Harvesting Function to make sure the environment at a
stable lux value
2. Dual PD to differentiate natural light and LED light
3. Wireless Pins to be easier installed on the LED light board
4. 15m high installation for UFO
5. 5 years warranty.
6. Remote control setting parameters
7. Microwaver Power lower than 0.3mW
8. Totally 11mm thickness, super thin for UFO/linear highbay
9. Module without housing to make it more flexible to be fixed.
Pattern of DC motion sensor:
| Pin setting +12v,GND,DIM+ Wireless Pins to be easier installed on the LED light board |
| 1.Mounting height,less than 15m/49.2ft (ceiling mounted) 2.Detection range,Max,ø14m/45.92ft (ceiling mounted) 3.Detection angle,30°-150° (without glass) |
| The sensor size is (L*W*H)34*33.5*11mm |
| Antenna module:Emit microwave signal,sense the motion of the object
Daylight sensor:Inducts the external light sensitivity threshold,
controls the lamp switch
|
Installation precautions of motion sensor:
1. Microwave sensor can be installed in any lamp except the one
with full metal shell.
2. The detected surface cannot be shielded by metal objects.
3. Make sure the microwave module is completely exposed outside.
4. The detection surface of the sensor module shall be installed
facing the detection area.
5. Should be kept away from the driver to avoid interference
generation and lamp flashing.
6. Wiring must be strictly in accordance with the wiring diagram to
avoid short circuit.
User Notes1.Microwave can penetrate walls or glass thinner than 20cm and
attenuate if thicker than 20cm.
2. The driver voltage shall be stable and float within 10%.
3. Detection area will be affected by speed of motion, mounting
height and movement volume.
4. Conduct test on sunny days without the lampshade which will
affect the tested lux value.
