Energy Saving Light Switches Microwave Motion Sensor Detached
Design Dimming Function
Features:
1. 5.8GHz microwave motion sensor with dimmable function.
2. Smart swithes and dimmers when detecting movement of objects.
3. Dual setting by DIP switch and remote control.
4. Tri-level control by 1-10v output.
5. Suitable for tri-proof light.
6. IP 20 with 5 years warranty.
7. Sensitive and reliable.
8. 8-15m high altitude installation.
Product Description
| Operating voltage | 120-240VAC,50/60Hz |
| Switching capacity | Max.200W(Control gear)Max.400W(Incandescent lamp) |
| Stand-by power | ≤1w |
| control method | on/off / 1-10v dimming/remote control |
| Microwave frequency | 5.8GHz±75MHz |
| Microwave power | <0.3mW |
| Detection area | 50%/100% |
| Hold time | 5s/30s/1min/10min |
| stand-by period | 0s/30s/20min/∞ |
| stand-by dimming level | 10%/20%/30%/50% |
| daylight threshold | 2Lux/10Lux/50Lux/Disable |
| interfaace | 6-pole pluggable clamp terminal(L,N,N,L',1-10V+,1-10V-,)for
0.75-1.5mm² cable |
| Mounting height | 8m-15m/26.25-49.2ft |
| deteation range | MaxØ14m/45.93ft |
| motion detection | 0.5–1,5m/s |
| operating temperature | –20℃–+55℃ |
| IP rating | IP 20 |
| Warranty | 5 years |
ON/OFF Control Detection Area Daylight Threshold Stand-by Period
Warranty 5 years Hold Time Stand-by Dimming Level 8-15m Highbay
Detection Range
This figure indicates the maximum distance at the highest mounting
height with 100% sensitivity.
Typical installation height 8-15m.
Mechanical structure
With nine DIP switch poles to set all parameters
With six poles to easily connect with LED driver and power supply
With two installation hole, easily fixed to the lighting fixture
for end user.
The separation of the sensor can be small to fit into the LED PCB
board
Detection Area:
In this area, movement will be detected and able to trriger the
sensor,100% detection area is known as the strong sensitivity.
Hold Time:
The period of light keeping 100% brightness after moving objects
leave the detection area.
Daylight Threshold:
Definition of the ambient brightness;only when the ambient
brightness is lower than the preset spcific lux amount,the sensor
will work;when it's preset as "disable",the sensor works everytime
it detects motion regardless the ambient brigtness.
Stand-by period:
The period of light keeping low output before it's compeletely
switched off,when it's preset as"∞" the light always keep at low
output if no movement in the detection area and doesn't turn off.
Stand-by dimming level:
The difinition of low output in the stand-by period.
Application Demo
1. Automatically ON/OFF function:
Light on when detect movement and off after people leave at night.
Applications: Corridor, Staircase.
With sufficient daylight, With insufficient daylight, After the
last detection and
even when motion detected, when motion detected, light ON. the
present hold time
light remains OFF. elapsed, light OFF.
2. No daylight function
The daylight threshold is set to "Disable".
Light on when detect movement, After people leave, Light off after
stand-by period.
Applications: Dim places such as Basement Parking, Underpass.
When motion is detected, After people leave the detection After the
last detection and
the sensor will switch on the area, light remains 100% the present
hold time
light to 100% brighteness. brightness within hold time. elapsed,
light OFF.
3.Function Demo-Dimmable control/Corridor function
With sufficient daylight, With insufficient After the last
detection, After the stand-by period
even when motion daylight when the light will be dimmed light off.
detected,light motion detected, down to the stand-by
remains off light on, dimming level
(10%,20%,30% or 50%)
after holdtime.
User Notes:
1.Microwave can penetrate walls or glass thinner than 20cm and
attenuate if thicker than 20cm.
2. The driver voltage shall be stable and float within 10%.
3. Detection area will be affected by speed of motion, mounting
height and movement volume.
4. Conduct test on sunny days without the lampshade which will
affect the tested lux value.
Memory & Apply Mode
1. Press "ON/OFF button" to turn on the light or off.
2. To reset the parameters, Please follow the steps as below:
Step 1 - Press ON, to turn on the light if it was off at the start.
Step 2 - Press "Start" to the well-setting sensor.
Step 3 - Press the button of Detection range, Hold time, Stand-by
dimming level,
Stand-by period and Daylight threshold one after the other in
sequence (Press "+/-" to
set parameters).
Step 5 – Press “Memory” to memorize the settings.
Note: The interval of each parameter setting shall be controlled
within 30s.
Isolated Setting Mode
1. Press "ON/OFF button" to turn on the light or off. Press
"Scene", the remote will
activate settings that were saved last or remain at the factory
default settings.
2. To reset the parameters, Please follow the steps as below:
Step 1 - Press ON, to turn on the light if it was off at the start.
Step 2- Press any button of "Scene", Test" and "Apply" to begin the
sensor detection
mode.
Step 3 - Press the button of Detection range, Hold time, Stand-by
dimming level,
Stand-by period and Daylight threshold one after the other in
sequence.
3. To programme other lights in the array that have similar sensors
to the same
programme.
Step 1 - Press "ON" to the second sensor
Step 2 - Press "Apply"
Notes:
1. Settings will be saved automatically and remain until you press
reset again.
2. Light will flicker when setting each parameter.
3. The icon will flash when setting the corresponding parameter.
HD05V-CRH
.pdf
