Automatic Motion Detected Daylight Sensor Planar Antenna For Panel
Light
Features:
1. Automatic ON/OFF control with daylight sensor.
2. Microwave frequency would be 5.8GHz±75MHz.
3. Optional detection range, holdtime and daylight threshold.
4. Set the parameters which you want by remote controller.
5. Compact size suitable for panel light.
6. Loop in and loop out for easy installation.
7. IP 20 with 5 years warranty.
Product Description
| Input voltage | Europe version:220~240VAC 50/60Hz
American version:120-277VAC 50/60Hz |
| Switching capacity | Europe version:Max.200W(120VAC),Max.400W(240VAC)
American version:Max.3.0A@120VAC,Max.2.0A@277VAC |
| Stand-by power | ≤1W |
| Detection area | 25%/50%/75%/100% |
| Hold time | 5s/30s/1min/3min/5min/10min/20min/30min |
| Daylight threshold | 2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/ Disable |
| Microwave frequency | 5.8GHz±75MHz |
| Microwave power | <0.3mW |
| Detection angle | 30°-150° |
| Mounting height | 2.5-6m/8.2-19.68ft (ceiling mounted) |
| Detection range | Radius, 3-6m/9.84-19.68ft (ceiling mounted) |
| Motion detection | 0.5~1.5m/s |
| Operating temperature | Ta: -25°C+60°C |
| IP rating | IP20 |
| Interfaces | 4-pole pluggable clamp terminal (L,N,N,L') for 1.5mm² cable. |
Detection area Daylight sensor Hold time
ON/OFF Control Warranty 5 years Remote Control
Detection Range
This figure indicates the maximum distance at the highest mounting
height with 100% sensitivity.
Typical installation height 2.5-6m.
Mechanical structure
With remote control to set all parameters.
With four poles to easily connect with LED driver and power supply.
4-pole pluggable clamp terminal(L,N,N,L')for 1.5mm² cable.
With two installation hole and two magnet, easily fixed to the
lighting fixture for end user.
Wiring diagram
Dimensions (mm)
Application Demo
1. Automatically ON/OFF function:
Light on when detect movement and off after people leave at night.
Applications: Corridor, Staircase.
With sufficient daylight, With insufficient daylight, After the
last detection and
even when motion detected, when motion detected, light ON. the
present hold time
light remains OFF. elapsed, light OFF.
2. No daylight function
The daylight threshold is set to "Disable".
Light on when detect movement, After people leave, Light off after
hold time.
Applications: Dim places such as Basement Parking, Underpass.
When motion is detected, After people leave the detection After the
last detection and
the sensor will switch on the area, light remains 100% the present
hold time
light to 100% brighteness. brightness within hold time. elapsed,
light OFF.
Installation Method:
User Notes:
1.Microwave can penetrate walls or glass thinner than 20cm and
attenuate if thicker than 20cm.
2. The driver voltage shall be stable and float within 10%.
3. Detection area will be affected by speed of motion, mounting
height and movement volume.
4. Conduct test on sunny days without the lampshade which will
affect the tested lux value.
Installation precautions:
1.Microwave sensor can be installed in any lamp except the one with
full metal shell.
2.The detected surface cannot be shielded by metal objects.
3.Make sure the microwave module is completely exposed outside.
4.The detection surface of the sensor module shfall be installed
facing the detection area.
5.Should be kept away from driver to avoid interference genaration
and lamp flashing.
6.Wiring must be strictly in accordance with the wiring diagram to
avoid short circuit.
Application Environment:
1.Suitable for indoor installation to avoid false triggering due to
external factors such as rain,wind or tree swing.
2.Shall not be installed in the place with all four metal shelters
and small space(such as galvanized-iron roof).
3.Shall note be mounted installation,so as to avoid false trigger
caused by the lamp itself shaking.
4.Shall not be installed next to large operating machines such as
ventilator/ceiling fan to avoid fase triggering caused by machine
vibration.
Application:
HD410SR.pdf
